Comments on: ORX Plus Tools 2PCS Deburring Chamfer Tool Set, Deburring External Drill Bit, Countersink Drill Bit for Fit 1/8″-3/4″(3mm-19mm)

By: Robert Hagen

Robert Hagen — Thu, 20 Feb 2025 12:06:00 +0000

Just used it to debur 4 long bolts I had to cut down on my trailer. It worked flawlessly.

By: Phil

Phil — Thu, 20 Feb 2025 12:06:00 +0000

Thanks!

By: Brian De Contreras

Brian De Contreras — Thu, 20 Feb 2025 12:05:59 +0000

It works well if you know the secret ð
Works well once you figure out the secret. When I first got this bit I was pretty upset It would chatter like a jackhammer and leave a horrible wavy jagged surface finish on the parts. It took a bit of trial and error to finally figure out that if I set my drill to the slow mode and basically use my whole body weight into the drill I would get very reliably smooth cuts. At that point I was pretty impressed, the surface finish is near mirror like most of the time. The only issue I have found is the small channels that are supposed to curl the chips and eject them sometimes will hold on to the aluminum. this may not be an issue with steel but with aluminum it definitely means a lot of manually clearing those chips with your finger or some sort of pick. I bought this bit specifically to chamfer 5/8 in 6061 aluminum for one of the parts we make, at this point we have done a few hundred of these pins and the bit works like a champ. Quite honestly with a hand drill and our custom soft jaws clamping the pin, chamfering, flipping, and chamfering the other side is so dang quick I’m not quite sure you could chamfer these parts in a manual lathe or mill anywhere as fast as this process. All in all I would recommend this product. But if it doesn’t work like intended play around with your drill pressure and speed.

By: jim chemsak

jim chemsak — Thu, 20 Feb 2025 12:05:59 +0000

Gives a good taper when used properly.
Great tool for tapering the ends of all thread rod, bolts, solid rod, steel & copper pipe (aluminum pipe is tricky). As others have said, DO NOT USE AN IMPACT DRILL!!! A small hand held battery drill is best, start at low speed and press lightly until desired taper is achieved. Hit it straight on, do not walk it around in a circle. If there is a burr on the work piece, say a cut off tip, grind or file it off first. This will keep the tool from giving you an off-center taper. Iâve used mine a dozen times w/o problem, still sharp.

By: RCOR

RCOR — Thu, 20 Feb 2025 12:05:59 +0000

Worth buying and works awesome
After reviewing many others, I decided to buy this ORX Plus Tools Deburring Drill Bit for bolt sizes 1/8″-3/4″.It has saved me a lot of time on projects, maintenance and repairs. I mainly use it on threaded bolts. It’s easy to use. It a quick attachment. The price is a little high but worth it. It’s been nine months and it still works like new. I use a little bit of oil every now and then, just like with my regular drill bits. I have used it over forty times and always gets the job done nicely.

By: Get some

Get some — Thu, 20 Feb 2025 12:05:59 +0000

Works great
What a surprise to use a cheap tool that actually works. Cuts like a hot knife through butter. Nuts thread on perfectly. Used on m6 and m10 bolts.

By: Connor Dion

Connor Dion — Thu, 20 Feb 2025 12:05:59 +0000

Great tool for unorthodox fixes
I never write reviews, but I felt that this thing deserves one considering how much money it saved me. If youâre here then you probably are hard up; having been through the wringer trying to find something locally that will fix your problem with a bolt that canât be replaced/changed. If so, then this is the tool you need. It âre-threadedâ the end of a frame mounted stud on my truck in less than 10 seconds and saved me a ton of cash in the end. Itâs high quality, strong and surprisingly durable. Get it!

By: Nicolai Reidovitch

Nicolai Reidovitch — Thu, 20 Feb 2025 12:05:59 +0000

Broke in less than a week of use
It worked very well for about 30 or so uses. The chuck snapped and now it is useless. If you do purchase this I’d advise against putting it in your impact. Use a drill instead. Not impressed with the quality *update * seller contacted me and replaced item for free. I appreciate this level of customer service

By: Mario

Mario — Thu, 20 Feb 2025 12:05:59 +0000

No durÃ³ ni 2 usadas. Se despega la cabeza del perno que se mete en el taladro.

By: Ryan carpenter

Ryan carpenter — Thu, 20 Feb 2025 12:05:59 +0000

Really happy with this. Many years as a builder struggling to get a treaded rod clean after cutting to length this eliminates all the stress and saves you time. Not 100% how long it will last but already saved me many ours work so itâs paid for itself. 10/10