Panasonic 30” Microwave Trim Kit for Panasonic 1.6 cu ft Microwave Ovens – NN-TK732SS (Stainless Steel)
Original price was: $299.95.$283.99Current price is: $283.99.
Price: $299.95 - $283.99
(as of Feb 06, 2025 07:13:14 UTC – Details)
Looking for a space-saving solution in your kitchen? Convert your Panasonic 1. 6 cu ft. countertop microwave oven to a built-in model with the Panasonic NN-TK732SS 30” microwave trim kit. This Trim Kit consists of the trim frame, an upper, lower, and rear duct that attaches to and encases the microwave inside the cabinet cut-out opening to give your kitchen a stylish look while freeing up precious countertop space. The Panasonic NN-TK732SS Trim Kit is designed for use only with the NN-SE7**S | NN-SD7**S | NN-SN7**S | NN-ST7**S Panasonic Microwave Ovens. For safety, unplug the microwave oven before attempting installation of the NN-TK732SS trim kit. Installation of this trim kit requires basic mechanical and electrical skills and may be completed by the DIY homeowner or kitchen cabinetry professional. Proper installation is the responsibility of the installer. The microwave oven must be used with a properly grounded 3-prong receptacle in compliance with the National Electrical code, as well as any applicable local regulations. Also refer to the microwave oven operating instructions for other safety and electrical requirements. This trim kit is only compatible with Panasonic Microwave Ovens.
Stainless Steel 30” Microwave Trim Kit compatible with 1.6 cu ft Panasonic Microwave Oven models including NN-SE7**S, NN-SD7**S, NN-SN7**S
Trim Kit Outer Size – 760mm or 30” (W) x 419mm or 16-1/2” (H) x 20mm or ¾” (D)
Trim Kit Inner Size – 22-5/8″ (W) x 11-5/8″ (H)
Required Cabinet Opening– 724mm or 28-1/2″ + 8mm or 5/16” – 0mm (W) x 389mm or 15-5/16″ +/- 2mm or 5/64” (H) x minimum 533mm or 21″ (D) and minimum 920mm or 36-1/4” from the floor
Tools Needed for Installation – Measuring tape, pencil, Phillips screwdriver, Ø 2 (5 /64″) mm drill
Customers say
Customers like the appearance of the microwave oven. They say it looks good and works well. However, some have issues with the gap size. There are mixed opinions on fit, ease of installation, sturdiness, value for money, and functionality.
AI-generated from the text of customer reviews
11 reviews for Panasonic 30” Microwave Trim Kit for Panasonic 1.6 cu ft Microwave Ovens – NN-TK732SS (Stainless Steel)
Add a review
Related Products
Original price was: $299.95.$283.99Current price is: $283.99.
F-111A –
It fits perfectly!
My old microwave died, so I bought a new Panasonic 1.6 cf one to replace the old one. The problem was the old one fit inside a custom cabinet, that was designed for it; apparently this was a valid size 30+ years ago, but is no longer the standard size. I bought the new one to fit in the cabinet, not realizing the old trim surround would no longer work. I then measured (and measured again) to make sure that the new Panasonic surround would fit…which it did (thank you, Amazon, for including the measurements for the product). The new Panasonic surround seems a bit pricey, but when it looks, and fits, as good as it does, the price issue goes away. The Panasonic surround is designed for the Panasonic microwave, and definitely enhances the look of the installation. I’m glad that this surround was available for me.
Dorca Torres –
Perfect!!
It fits perfectly for my microwave, Great
M. Findlay –
Nice to Look At, but a bit difficult to install
I had regrets about paying so much for a “trim kit”, as it cost almost as much as the microwave.But then, I am anal about how things look in our remodeled kitchen and this kit looked really nice in the photos.I also liked that this kit had openings or vents in the front for dissipating heat from the microwave. I avoided cheaper trim panels with no holes for ventilation.When the kit arrived–and it’s packaged incredibly well in custom designed foam padding, I was impressed to see all that comes with this kit. I just really expected the face trim, but the kit comes with a sheet metal base that has rails built-in to support the feet of the microwave and lift it off the cabinet bottom for better ventilation and better centering in the opening. I had just finished making my own wooden supports for the feet, but nothing as good as what this kit offers. It’s odd that you have to bend the internal vent shroud into shape, as opposed to a preassembled shroud coming with the kit, and the instructions are not perfect and I bent into the reverse image which wouldn’t work, and had to re-bend the entire shroud (the Shroud of Turning). Not all the instructions fault, as I had a power failure the night of installation and bent by flash light…Was disappointed the face kit would not fit my cabinetry, as I have 1-1/2″ wide cherry trim, and the kit is made ONLY for cabinets with 3/4″ thick walls (the included face trim supports will NOT accommodate cabinets with face trim). Other reviewers were forced to drill holes in the face plate and mount with stainless steel screws and throw their nice little support pieces away. I was able to drill pilot holes in my cherry trim centered on each of the 4 square holes in the back of the trim plate and hang on four 1-1/2″ No 10 round head screws whose head barely fit through the square holes. Need to measure carefully for these four holes in my trim, but I used the foam insert that came with the packaging as a template as it’s exactly the width (30″) of the face. Trim Plate looks great, with no evident means of support, but this kit takes some work to fit any odd size cabinet. Still, it was worth the effort as the wife gave it her blessing.
Amazon Customer –
Not for microwave model Panasonic NN-SN766S
The trim kit is larger than Panasonic microwave model NN-SN766S that it is supposed to be compatible with. This means that there is a space between the microwave and the trim leaving a visual hole. I did not expect this since ordering a Panasonic microwave and the corresponding trim kit. I had already folded and applied the left duct, returning the trim kit was not an option.
Cha0tic –
Installed perfectly
We are very pleased with how easy this was to install and how great it looks in the kitchen.
Han Solo –
NOT so easy to install UNLESS your cabinet hole is exactly the right size.
The trim actually does fit around the microwave properly. You are supposed to leave space so that the door opens properly. From a distance, the extra space looks black and professional and is probably about 1/2″ around the width ends and perhaps a little less on the top and bottom. The material for the shunt to bring the exhaust forward through the vents is rudimentary and requires the use of tape, which is pretty lame. Even so it still works.My main concern is NOT one raised by others. This is that the design requires that the cabinet hole have a width that is about 24″ and ideally a height that is probably closer to 14″. In other words, the points of connection are FIXED for precise dimensions on the back of the trim. Whatever the exact dimension is, enough) you CANNOT align all four connecting points UNLESS your hole is the perfect height and at least beyond a certain width. This means you either need someone to cut your hole (if it’s too small) or else the unit is only connected at 2 points to the cabinet.The other concerns are that it would have been better if there were a way to put a screw through the trim without marring the mirror-like finish, but there isn’t. Other trim designs allow for holes to screw into the cabinetry. The actual trim itself is beautiful, but it is cheap and very flimsy like a soft aluminum. If you don’t look closely it will be fine. I also found it was actually a little shorter than my hole and so I had to position it just right so you didn’t notice the gaps (would have been nice to have more material to work with. There’s also no easy adjustment on the height of the microwave so I found I had to buy a piece of wood to go under the existing stand to align it properly.So how else can you attach it if you can’t align the hardware? There are 2 possibilities that I thought of. First, you can get a screw that you put into your cabinet to match up with the holes at four points into the frame. This requires very precise placement and is NOT easy to do. Second, you can actually fill the side lengths with wood cut to fit there and glue those pieces to your cabinet frame. This is what I ended up doing.
artie –
Trim kit fit perfectly, installation was straight forward but follow instructions. Most important, looks great..
Kingston ontario customer –
It is a very good oven trim kit. It looks great, it made stainless steel. very happy
Liz –
So far it looks very nice, not installed yet, but will be a lovely addition to my new kitchen
I.W. –
It looks great!
BMBM –
Not happy with mounting method. Way too specific placement / dependent on openi g cut out dimensions. Works ok I guess for new build cabinetry but no good for my existing openimg cut out.Had to get 4 new cleat/tab brackets fabricated to mount it.This trim with vents is for micro. cabinet without back or top venting.Has approx. 1/2 ” thickness (projection from front face of cabinet).