SMARTSTANDARD 6.8FT Barn Door Hardware Kit, Sliding Barn
$28.99
Product Overview
The SMARTSTANDARD 6.8FT Barn Door Hardware Kit offers a complete, ready-to-install solution for transforming your space with a sleek barn door. Designed specifically for interior use, this system features a durable steel rail that supports smooth, quiet sliding motion for up to a 40-inch wide door panel. Whether you’re renovating a bedroom, bathroom, closet, or living area, this kit combines modern aesthetics with practical functionality. Engineered for reliability and ease of use, it includes all necessary components—from hangers to safety stops—and comes with clear, step-by-step instructions to simplify installation even for DIY beginners. With thoughtful design elements like anti-jumper discs and an adjustable floor guide, the system ensures secure operation while maintaining a clean, clutter-free environment.
Key Features
- Smooth and Quiet Operation: The J-shape hangers glide effortlessly along the full-length track, minimizing friction and noise for a peaceful daily experience. This makes the system ideal for bedrooms or shared spaces where quiet movement is essential.
- Easy Installation: No professional help required. The kit includes comprehensive, illustrated instructions that walk you through each step, from marking wall studs to final tightening. All tools and anchors needed are included, streamlining the entire process.
- Adjustable Door Stoppers (2): These slide freely along the rail and lock securely at any position, allowing you to stop the door exactly where you want—whether halfway open or fully closed. Rubber-capped ends provide soft, silent contact to prevent banging or damage to walls.
- T-Shaped Floor Guide Included: Positioned on the floor beneath the door, this guide prevents swinging, lifting, or misalignment by keeping the door centered on the track. It’s especially useful in rooms with limited clearance or high foot traffic.
- Anti-Jumper Discs (2): Small but critical safety components, these round discs attach to the top edge of the door. They physically block the door from being lifted off the track unless manually removed—adding an extra layer of security against accidental disengagement.
Technical Specifications
- Track Length: 6.8 feet (approximately 2.1 meters)
- Maximum Compatible Door Width: Up to 40 inches (101.6 cm)
- Included Components:
- One 6.8-foot steel sliding rail
- Two J-shape door hangers
- Two adjustable door stoppers with rubber caps
- One T-shaped floor guide with mounting hardware
- Two anti-jumper discs
- Installation anchors and screws
- Detailed, illustrated instruction manual
- Intended Use: Interior flat-panel doors only; not suitable for hollow-core exterior doors or glass panels without structural reinforcement.
Benefits & Use Cases
This barn door hardware kit excels in residential settings where space efficiency and contemporary style are priorities. It’s particularly effective in narrow hallways, small bathrooms, or closets where traditional swing doors would obstruct movement or furniture placement. The 6.8-foot track fits standard doorway openings commonly found in homes built after the 1950s, making it a versatile choice across many renovation projects.
Safety and stability are built into every component. The anti-jumper discs eliminate the risk of the door accidentally rising off the track—a common concern with lighter doors or households with children. Meanwhile, the T-shaped floor guide maintains consistent alignment, reducing wear on both the door and track over time. Adjustable stoppers offer flexibility: you can set the door to stay partially open during ventilation in a laundry room or remain fully closed for privacy in a master bedroom.
Because the system mounts directly to wall studs or uses included anchors for secure attachment, it delivers reliable performance without requiring complex modifications. Once installed, the door glides silently, creating a serene atmosphere ideal for relaxation or focused work areas.
Important Notes
- A minimum vertical clearance of 6 inches (15.2 cm) is required from the top of your door to the ceiling, crown molding, or any overhead structure above the doorway. Insufficient space may prevent proper fit or cause binding during operation.
- If wall studs do not align with the pre-drilled holes in the rail, or if your doorway has trim that adds depth, a headboard (an optional support board behind the rail) may be necessary. Specifically, if the combined thickness of the door plus trim exceeds 2 inches, additional support becomes essential to maintain level tracking.
- This kit is designed exclusively for flat-panel interior doors. It does not accommodate hollow-core exterior doors, double-layered glass panels, or specialty door types without prior consultation and potential reinforcement.
- Always follow the provided installation instructions carefully. Proper alignment, secure anchoring, and correct placement of all components are critical for safe, long-lasting performance. Skipping steps or using incorrect fasteners may compromise stability and safety.
9 reviews for SMARTSTANDARD 6.8FT Barn Door Hardware Kit, Sliding Barn
Add a review
Related Products
Sliding Barn Door Hardware Kit, VEVOR 8FT 330LBS Heavy Duty
Fredbeck 36×84 inch White Barn Door with 6.6FT Sliding Door
Dirtbaby13 –
Amazing quality DYI door
This door is amazing quality wood, easy to follow directions and assembly. One issue, we did not receive the correct size rail, but it still worked for us. The rail went up with no issues and the door slides with ease. Good quality heavy hardware- esthetically pleasing! Also, for all the DYIâers we needed a slightly shorter door, we were able to customize it to make it fit with ease. Great buy worth every dollar!
mark –
Happy wife
Great product super strong very good looking
silver stream :) –
Better than expected
I was pleasantly surprised by the quality of this item. Itâs better than items usually âmade in Chinaâ. The instructions are exceptional, the English is really solid and the measurements are all in inches.I am including a snapshot of page 2 of the instructions that I thought would have been helpful to see before I purchased the hardware. It lays out all the requirements for clearances.You will want to check to make sure that if your floor is sloped somewhat, that you plan for the proper floor to door clearance on the tight end so that your door will not bind when rolled that direction. It goes without saying if you follow the directions, but you will want the rail to be level instead of parallel to the floor.
Stan Krajcik –
very inexpensive kit
worked very well
R2 –
Nice solution, but not for the faint of heart. Questionable parts quality.
First of all, we really like the look and function of the rolling hardware. Would we buy again, yes! However, the installation is not for someone who thinks they’ll just drill a few holes and slap it up on the wall. We bought two sets that spanned a total of 20ft. Each of the two doors weighed about 85lbs. One set of tracks matched up to the studs behind the sheetrock really well. One did not match any of the pre-existing holes with studs behind the wall. Now that was NOT the manufacturer’s fault. My house was just built by someone who could not measure very well. And, it was far from easy to drill new holes in the steel. My biggest piece of advice….get and use a level at every step along the way. Check it, then check it again, then check it again….at every step along the way.The instructions were straightforward and easy to follow along. The packaging and layout of the hardware were well done. However, two of the bolts that held the rollers to the barn door stripped out once we applied the hex nut to the end of the bolt – meaning, there was nothing to screw into. I replaced the bolts, but it was impossible to find black and metric bolts to match what came in the package. So, I’m currently stuck with silver bolts/nuts in two places. If the manufacturer wants to send me new hardware, I’ll be happy to adjust the Value for Money rating to 5/5.
Cymba –
Excellent quality, looks nice and reasonably priced.
I built my husband a barn door for his man cave for Christmas and used this hardware kit to hang the door. The door i built was 49″Ã82″ and 1.5″ thick at the edges so it was pretty heavy and needed a good rail to hold it. I think this rail is rated for up to 250 lb door.I opted to install a header board into the studs then mount the rail on the header board. (Also the rail is predrilled so if you have an older house the holes may not line up exactly with the spacing of your wall studs.) Using a header board worked out great, the door is well supported. It looks nice, and complements the door wood. The door glides smoothly on the rollers and the track stops have rubber cushions so the door opens and closes softly.I did not like the floor guide thats included because you have to groove the bottom of the door for it to work. This was not a good option for the way i constucted my door. I would recommend picking up a wheel floor guide, it works out so much better and theres no need to groove the door or drill into your flooring.
Bill –
Still had to drill my own holes, but learn from my mistake
I have a 30″ arched doorway in my master bedroom that I needed to enclose to the master bathroom. Since it was so narrow I didn’t want to put a door there, and it would had to have been custom made. I decided to do a barn door to cut down on the noise my wife makes getting ready in the morning. I built the door and needed hardware to hang it. The big box home improvement stores sell kits for $150+. There is absolutely no reason to spend the money on those, when this is half the price and functions exactly the same. Due to the stud location on the wall, I was not able to hit studs where the factory holes were. It would have pushed the bar too far down and wouldn’t have been able to open the door the whole way. Here is where I made my mistake. I decided to drill new holes to line up with my studs and it worked fine. I have extra holes, but nobody has noticed them so it’s not a huge deal. An even better way to do it, is to use a 1x backer for the bar to mount to. You can go to your local home improvement and pick up a piece of 1×6 (or any width you want). You mount the 1x backer to your wall and attach it to studs. Since the 1x is on the wall, you can mount the bar to that instead. 1x will have the strength to support your door easily since it’s mounted to studs (I would use 3″ high quality exterior screws two per stud.) I do plan to take mine down and do something similar so it matches the trim in my room. I like the hardware because it’s very quiet, very heavy duty, and significantly cheaper than anywhere else. I did not use the guide for the door because I didn’t want to drill in my new wood floors. I ended up buying a barn door wheel and having it modified to work for me. The guide would probably work great if you can use it. Just keep in mind you will need to run your door down the table saw to get a groove in it for the guide. It’s actually pretty easy to do.
Paige Hill –
Awesome slider for the money
Used on our homemade greenhouse, went together perfectly and is holding a 40lb wood and glass door. Slides like butta baby.Chose this as we live in a deep snow zone, instead of shoveling a ton of snow to open a standard door, we’ll only need to create a channel if we need to get inside.
Yara corro –
El producto es lo que esperaba, llegó a tiempo y el vendedor me dio muy buena atencion